electro-music.com   Dedicated to experimental electro-acoustic
and electronic music
 
    Front Page  |  Articles  |  Radio
 |  Media  |  Forum  |  Wiki  |  Links  |  Store
Forum with support of Syndicator RSS
 FAQFAQ   CalendarCalendar   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   LinksLinks
 RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in  Chat RoomChat Room 
Live streaming at radio.electro-music.com

  host / artist show at your time
  Jez Adventures in Sound
Please visit the chat
 Forum index » Clavia Nord Modular » Nord Modular G2 Discussion
Anyone know of a module(s) that does what I'm looking for?
Post new topic   Reply to topic Moderators: Nord Modular Editors
Page 1 of 1 [6 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
Author Message
zynthetix



Joined: Jun 12, 2003
Posts: 838
Location: nyc
Audio files: 10
G2 patch files: 13

PostPosted: Wed Jul 21, 2004 6:27 pm    Post subject: Anyone know of a module(s) that does what I'm looking for? Reply with quote  Mark this post and the followings unread

This might have an obvious answer to some, but none of the logic/switch modules (at least the combinations I've tried) seem to do this. Please use the diagram below as reference. I am looking for some kind of module/combination (represented by the "?") that has one input for a note/gate/on event, 2+ possible outputs for routing that event, and another input for a control signal that determines which output the note/gate/on event will route through.

My idea is that an LFO/osc could be used as a control source for the "mystery router"...if the sine wave in the control LFO is 0<+64 units, the note/gate/ on event will go out myster router ch. 1, hence triggering Oscillator 1 in the diagram. If the sine wave of the control LFO is -64>0, the note/gate on event will go out myster router ch. 2, hence triggering Oscillator 2.

Any suggestions? I would be surprised if there is not a simple way to do this I have overlooked/don't understand entirely. Sorry for the verbose description, I hope its more helpful than confusing.


nordquestion1.gif
 Description:
 Filesize:  5.28 KB
 Viewed:  1977 Time(s)

nordquestion1.gif


Back to top
View user's profile Send private message AIM Address
zynthetix



Joined: Jun 12, 2003
Posts: 838
Location: nyc
Audio files: 10
G2 patch files: 13

PostPosted: Wed Jul 21, 2004 6:29 pm    Post subject: Reply with quote  Mark this post and the followings unread

Just another comment, but I essentially want an LFO to control the "radio buttons" (i.e. what output channel) on a switch module instead of pressing the buttons manually.

:edit: Silly of me not to specify, but I'm using the Nord G2 as opposed to the original modular. :/edit:
Back to top
View user's profile Send private message AIM Address
egw



Joined: Feb 01, 2003
Posts: 1511
Location: Asheville NC
G2 patch files: 8

PostPosted: Wed Jul 21, 2004 7:00 pm    Post subject: Reply with quote  Mark this post and the followings unread

Can't you use a pan module for that?
Back to top
View user's profile Send private message Visit poster's website
jamos



Joined: Jun 01, 2004
Posts: 470
Location: Eugene, Oregon, USA
Audio files: 4
G2 patch files: 36

PostPosted: Wed Jul 21, 2004 7:29 pm    Post subject: Reply with quote  Mark this post and the followings unread

The Mux 1-8 should do that; you'd need to add some level shifting and scaling ahead of the control input to ensure that only the first two outputs are used.
Back to top
View user's profile Send private message Send e-mail Visit poster's website
ian-s



Joined: Apr 01, 2004
Posts: 2575
Location: Auckland, New Zealand
Audio files: 42
G2 patch files: 608

PostPosted: Wed Jul 21, 2004 8:30 pm    Post subject: Reply with quote  Mark this post and the followings unread

Probably lots of ways to do this but I would go for a combination of the level compare and a couple of value switches. The knob on the level compare lets you set the swap point (if you wanted to bias the output one way or the other). To switch the gate and note values you need a pair of switches.
More than two outputs would require a different solution.
Or you could create a chained network with multiple instances of this technique.


router.gif
 Description:
 Filesize:  5.64 KB
 Viewed:  1966 Time(s)

router.gif


Back to top
View user's profile Send private message
zynthetix



Joined: Jun 12, 2003
Posts: 838
Location: nyc
Audio files: 10
G2 patch files: 13

PostPosted: Wed Jul 21, 2004 8:52 pm    Post subject: Reply with quote  Mark this post and the followings unread

Thank you for the input everyone. The pan module would be the simple solution that I figured was evading me, but these other alternatives are definetly worth toying with (I will need more than 2 outputs in most situations.) Thanks again, I'll post some patches involving this when I finish.
Back to top
View user's profile Send private message AIM Address
Display posts from previous:   
Post new topic   Reply to topic Moderators: Nord Modular Editors
Page 1 of 1 [6 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
 Forum index » Clavia Nord Modular » Nord Modular G2 Discussion
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
e-m mkii

Please support our site. If you click through and buy from
our affiliate partners, we earn a small commission.


Forum with support of Syndicator RSS
Powered by phpBB © 2001, 2005 phpBB Group
Copyright © 2003 through 2009 by electro-music.com - Conditions Of Use