Benjolin easy battery connect

[electri-fire]

Due to lack of time we didn't get to connect the batteries at the workshop building the Benjolin, so the circuitboards were tested with Rob's optional In/out board.

I soldered the battery holders myself later, but made a mistake. So my Benjolin got hot and smelly, I hope it still works.

Here's how it should/could be done (if you do not have the female header connectors that could also be used and make it look more slick)

Looking at the solderside the voltageconverter transistors are at the upper right corner. The left of these is for -9V, the one to the right provides +9V.

The + and - 9 volt voltage regulators need 2-3 volts surplus to work properly so at he header side you could use 12-15 volts.

Batteries need to be connected at the output of the regulators, here two male headers (connectors) are available at the circuitboard.

I included a JPG to indicate how to connect batteries if you do not use the female connectors for the battery headers. Note: the black wire of the + voltage and the red wire of the - voltage battery go to ground.

---

Benjolin easy battery connect.jpg
Description:	How to connect batteries to the Benjolin without header connectors.
Filesize:	29.16 KB
Viewed:	14725 Time(s)

---

[State Machine]

[bugbrand]

Seeing as I didn't know what a Benjolin was I did a search and found the site - looks interesting!

One thing I noticed from the picture was that the ICs don't all face the same way! That is always a dangerous way to go... especially without sockets. I always provide sockets with workshop orientated kits otherwise people are bound to make mistakes!



PS - electri-fire - I see you're in Breda - do you know Tom Tok Tek?

[Danno Gee Ray]

Here is my Completed case for the Benjolin.

I agree that sockets would have been greatly appreciated. The PCB was very high quality for a home etched unit. Kudos to Rob and Joker for the workshop.

---

S7300272.JPG
Description:
Filesize:	1.78 MB
Viewed:	519 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.

---

---

S7300273.JPG
Description:
Filesize:	1.78 MB
Viewed:	428 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.

---

---

S7300274.JPG
Description:
Filesize:	1.76 MB
Viewed:	424 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.

---

---

S7300275.JPG
Description:
Filesize:	1.76 MB
Viewed:	411 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.

---

---

S7300276.JPG
Description:
Filesize:	1.68 MB
Viewed:	392 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.

---

[Danno Gee Ray]

A couple more...

---

S7300278.JPG
Description:
Filesize:	1.8 MB
Viewed:	450 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.

---

---

S7300279.JPG
Description:
Filesize:	1.8 MB
Viewed:	427 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.

---

---

S7300280.JPG
Description:
Filesize:	1.76 MB
Viewed:	420 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.

---

[Danno Gee Ray]

Here's the labels for the knobs.

---

S7300285.JPG
Description:
Filesize:	1.76 MB
Viewed:	391 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.

---

[modulator_esp]

Wow, that is nice work, you were right about the case

[State Machine]

Holy cow Dan !!! That is really beautiful. I love it. Looks like a hard drive enclosure. Nice idea !! Now you have no excuse not to jam at EM 2010

I have mine and studied the circuit one more time ...

Bill

[electri-fire]

Whoa Danno, you're fast, we built this board last saterday.

Anyway, labeling seems a good idea, I scribbled the names on my board with a marker for lfuture reference. Saves me from checking the schematic later.

(note: Dan's cicuitboard is mounted with the two headers on the left side)

[Danno Gee Ray]

Thanks,

Yes it is a Hard Drive enclosure. The USB circuit in the enclosure had failed. Seemed just perfect use for the thing.
Worked on the case two days straight. I rather like it.

[Danno Gee Ray]

Just figured out that in my haste, I put the knob labels on incorrectly. I've replaced the photo. Sorry for the fuzzy image.

[electri-fire]

So, lables according to Dan:

---

benjolin knob labeling.jpg
Description:	Benjolin circuitboard with the knobs labeled
Filesize:	59 KB
Viewed:	430 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.

---

[Danno Gee Ray]

Yes, see this link for verification:

http://web.me.com/klangbureau/DIY/making_of.html

[mono-poly]

I want a Benjolin to.