electro-music.com   Dedicated to experimental electro-acoustic
and electronic music
 
    Front Page  |  Articles  |  Radio
 |  Media  |  Forum  |  Wiki  |  Links  |  Store
Forum with support of Syndicator RSS
 FAQFAQ   CalendarCalendar   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   LinksLinks
 RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in  Chat RoomChat Room 
 Forum index » DIY Hardware and Software » Circuit Bending
Fixing the 3.5mm stereo output on a Casio MT-205
Post new topic   Reply to topic Moderators: dnny, v-un-v
Page 1 of 1 [4 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
Author Message
destroyifyer



Joined: Mar 22, 2006
Posts: 426
Location: Babylon
Audio files: 4

PostPosted: Thu Dec 31, 2009 2:47 am    Post subject: Fixing the 3.5mm stereo output on a Casio MT-205 Reply with quote  Mark this post and the followings unread

The stereo output is audible only through the left channel- the right channel can barely be heard, panned heavily and turned up very loud. I predict I will have to replace the stereo out... is there anything I can do to avoid this or should I just go ahead and give it a shot? I tried cleaning the jack with a stripped q-tip and some rubbing alchohol... didn't work... don't have any more ideas, really. Any help or suggestions would be slightly appreciated.

Thanks, from Kyle
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Danno Gee Ray



Joined: Sep 25, 2005
Posts: 1343
Location: Telford, PA USA

PostPosted: Thu Dec 31, 2009 7:54 am    Post subject: Reply with quote  Mark this post and the followings unread

Might want to check the signal level coming into jack to see if one of the output channels is failing.
Back to top
View user's profile Send private message
imaguitargod



Joined: Jun 14, 2008
Posts: 56
Location: Cleveland

PostPosted: Thu Dec 31, 2009 7:55 am    Post subject: Reply with quote  Mark this post and the followings unread

Sounds, to me in my limited experience, that the wire going to the right channel peg on the jack is loose. Open it up and check her out. May just need a dab of solder.
_________________
Assistant brewer for Hoppin' Frog Brewery
My Noise Project: I Like Pie (MySpace Page)
Back to top
View user's profile Send private message Visit poster's website AIM Address
destroyifyer



Joined: Mar 22, 2006
Posts: 426
Location: Babylon
Audio files: 4

PostPosted: Thu Dec 31, 2009 4:24 pm    Post subject: Reply with quote  Mark this post and the followings unread

Well, thank you I might give this a whirl. If all else fails I suppose I'll rip out the built-in speakers (they sound horrible anyways) and route those to a new jack, maybe to avoid messing with the circuit board.

Thanks, and an interesting and eventful new decade to you all.
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic Moderators: dnny, v-un-v
Page 1 of 1 [4 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
 Forum index » DIY Hardware and Software » Circuit Bending
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
e-m mkii

Please support our site. If you click through and buy from
our affiliate partners, we earn a small commission.


Forum with support of Syndicator RSS
Powered by phpBB © 2001, 2005 phpBB Group
Copyright © 2003 through 2009 by electro-music.com - Conditions Of Use