electro-music.com   Dedicated to experimental electro-acoustic
and electronic music
 
    Front Page  |  Articles  |  Radio
 |  Media  |  Forum  |  Wiki  |  Links  |  Store
Forum with support of Syndicator RSS
 FAQFAQ   CalendarCalendar   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   LinksLinks
 RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in  Chat RoomChat Room 
Live streaming at radio.electro-music.com

  host / artist show at your time
  mosc Back on the air tonight - Twyndyllyngs
Please visit the chat
 Forum index » DIY Hardware and Software
DS 7 clone
Post new topic   Reply to topic Moderators: jksuperstar, Scott Stites, Uncle Krunkus
Page 18 of 18 [427 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
Goto page: Previous 1, 2, 3, ..., 16, 17, 18
Author Message
Starspawn



Joined: Jun 14, 2013
Posts: 39
Location: Oslo

PostPosted: Sun Jul 20, 2014 4:06 pm    Post subject: Reply with quote  Mark this post and the followings unread

Here you go, still missing a few extras for the other pads, but sounds nice imo, good low end.

Toothbrush is is an invaluable stripboard tool, when scoring lines (after soldering to prevent tiny shorts) I put alcohol on and brush away the junk Wink


Posted Image, might have been reduced in size. Click Image to view fullscreen.
Posted Image, might have been reduced in size. Click Image to view fullscreen.

And sounds, just put them hard panned straight into recorder and played for a little while.

https://soundcloud.com/vintersmokk/ds7-mutand-sounds-first-try
Back to top
View user's profile Send private message
tokyomatik



Joined: Jan 20, 2011
Posts: 123
Location: berlin
Audio files: 6

PostPosted: Thu Sep 18, 2014 6:12 am    Post subject: Re: DS7 mods Reply with quote  Mark this post and the followings unread

dnny wrote:
so here are some pics of DS7 mods

first there is the VCA input mod. (for signal not for CV)
run wire from jack to leg 3 of CA3080 via 100K resistor and 100K pot.
to the panel you ad VCA input (jack) and VCA input level (pot)

and second comes the manual trigger mod:
run wire from +9V via 1M resistor to momentary push button and from there to trigger sens pot point 3.
to the panel you ad momentary push button.

(you get continuos signal if you hold the button down.)

daniel

ps. the RJWsofts Schematic Publisher is great and the pics are made whit it.
Schematic Publisher free download

I'm trying this mod on a DS8 euro module so we are not dealing anymore with +9v but with +12v.....should I change the resistor value? Any advice?
Back to top
View user's profile Send private message Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic Moderators: jksuperstar, Scott Stites, Uncle Krunkus
Page 18 of 18 [427 Posts]
View unread posts
View new posts in the last week
Goto page: Previous 1, 2, 3, ..., 16, 17, 18
Mark the topic unread :: View previous topic :: View next topic
 Forum index » DIY Hardware and Software
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
e-m mkii

Please support our site. If you click through and buy from
our affiliate partners, we earn a small commission.


Forum with support of Syndicator RSS
Powered by phpBB © 2001, 2005 phpBB Group
Copyright © 2003 through 2009 by electro-music.com - Conditions Of Use