electro-music.com   Dedicated to experimental electro-acoustic
and electronic music
 
    Front Page  |  Radio
 |  Media  |  Forum  |  Wiki  |  Links
Forum with support of Syndicator RSS
 FAQFAQ   CalendarCalendar   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   LinksLinks
 RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in  Chat RoomChat Room 
 Forum index » DIY Hardware and Software » Thomas Henry designs
[SOLVED] -- Error in Mag Smoke Documentation for TH-102???
Post new topic   Reply to topic Moderators: Scott Stites
Page 1 of 1 [3 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
Author Message
AlasdairMoons



Joined: Dec 03, 2011
Posts: 105
Location: East-Belgium

PostPosted: Sun Jul 27, 2014 1:38 pm    Post subject: [SOLVED] -- Error in Mag Smoke Documentation for TH-102??? Reply with quote  Mark this post and the followings unread

hi guys,

I'm near to finish the Magic Smke Board Rev. 2 for the TH-102 ..

in the doc there is some switching I do not understand , is it possible that there is an error??
all things to CN103???

CN13 and CN14 are not mentioned anywhere else in the cabling doc .. so I think it must be like marked in red on image below ..


Rev02-Error.jpg
 Description:
 Filesize:  26.77 KB
 Viewed:  5205 Time(s)

Rev02-Error.jpg



_________________
greetings from belgium, Sascha

my DIY-blog: http://ardvinnamodular.blogspot.be
my DIY Youtube-Channel: https://www.youtube.com/channel/UCWAR64-81C3FbK_Hejz2QHw
my Music-Channel:
https://www.youtube.com/channel/UCzTd_AEK6CVM4gn325wvjYQ
my Facebook:
https://www.facebook.com/AlasdairMoon

Last edited by AlasdairMoons on Mon Jul 28, 2014 1:26 am; edited 1 time in total
Back to top
View user's profile Send private message Visit poster's website
elmegil



Joined: Mar 20, 2012
Posts: 2177
Location: Chicago
Audio files: 16

PostPosted: Sun Jul 27, 2014 8:15 pm    Post subject: Reply with quote  Mark this post and the followings unread

I posted this in the other thread as well; you are correct. Here's a rundown of all the connectors:

Quote:

If you're looking for a little more info on the board image I posted, here are the connector functions:

Left Edge:
CN7 Linear CV In jack
CN8 Linear CV attenuator
CN1 Coarse Tune
CN2 Fine Tune
CN101 FM 2 In jack
CN102 FM 2 attenuator

Top Edge:
CN105 Square Suboctave out
CN110 Pulse Suboctave out
CN108 PWM In attenuator
CN107 PWM In jack
CN106 PWM Initial
CN109 Pulse Out
CN104 Rampoid Out
CN15 Tri - Ramp / Sine Out
CN16 Square Out

Bottom Edge:
CN4 1V/Octave CV in (switching jack)
CN3 Keyboard CV in (from internal bus)
CN6 FM 1 In attenuator
CN5 FM 1 In jack
CN9 Skew Initial
CN10 Skew CN In jack
CN11 Skew attenuator
CN103 Hi / Low cap switch
CN12 Sync In

Middle:
CN13 S1a (Tri - Ramp / Sine Select switch)
CN14 S1b (Tri - Ramp / Sine Select switch)

Right Edge:
CN17 DC Power In (4 pin .156" Blacet style)
CN18 & CN19 DC Power In (6 pin .100")

Whew! Lotsa connectors. But we do have
* Tri -Ramp / Sine Out
* Pulse Out (derived from Tri - Ramp)
* Suboctave (derived from Pulse)
* Square Out
* Suboctave (derived from Square)
* Rampoid Out

* Two Expo FM Inputs with attenuators
* Linear CV Input with attenuator
* 1V/Octave CV Input

* Tri - Ramp Skew CV Input with attenuator
* PWM Input with attenuator

* Sync Input
Back to top
View user's profile Send private message
AlasdairMoons



Joined: Dec 03, 2011
Posts: 105
Location: East-Belgium

PostPosted: Mon Jul 28, 2014 1:24 am    Post subject: Reply with quote  Mark this post and the followings unread

Thanks elmegil ..

I got an answer yesterday from Tim ..

Error is correct .. the Tri/Sin Switch is connected to CN13 CN14

_________________
greetings from belgium, Sascha

my DIY-blog: http://ardvinnamodular.blogspot.be
my DIY Youtube-Channel: https://www.youtube.com/channel/UCWAR64-81C3FbK_Hejz2QHw
my Music-Channel:
https://www.youtube.com/channel/UCzTd_AEK6CVM4gn325wvjYQ
my Facebook:
https://www.facebook.com/AlasdairMoon
Back to top
View user's profile Send private message Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic Moderators: Scott Stites
Page 1 of 1 [3 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
 Forum index » DIY Hardware and Software » Thomas Henry designs
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Forum with support of Syndicator RSS
Powered by phpBB © 2001, 2005 phpBB Group
Copyright © 2003 through 2009 by electro-music.com - Conditions Of Use