electro-music.com   Dedicated to experimental electro-acoustic
and electronic music
 
    Front Page  |  Radio
 |  Media  |  Forum  |  Wiki  |  Links
Forum with support of Syndicator RSS
 FAQFAQ   CalendarCalendar   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   LinksLinks
 RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in  Chat RoomChat Room 
 Forum index » DIY Hardware and Software » YuSynth
ADSR new version
Post new topic   Reply to topic Moderators: Scott Stites
Page 1 of 1 [8 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
Author Message
ludo



Joined: Sep 20, 2018
Posts: 4
Location: Berlin

PostPosted: Thu Sep 20, 2018 1:19 pm    Post subject: ADSR new version Reply with quote  Mark this post and the followings unread

I built the new version of yusynth´s ADSR, it works but there is no affect in the decay and sustain pots. What could be wrong?

Thanks a lot - Lu
Back to top
View user's profile Send private message
Grumble



Joined: Nov 23, 2015
Posts: 1294
Location: Netherlands
Audio files: 30

PostPosted: Thu Sep 20, 2018 10:36 pm    Post subject: Reply with quote  Mark this post and the followings unread

you wil notice that the forum will be much more responsive if you:
1 provide some more info like a link to your project, or a schematic...
2 write down what is working and what is not
3 write down what you have done so far to eliminate your problem
4 post pictures, soundbytes or anything to make it easyer to help you out.
these are just some hints you could follow to get the best of the forum for now (for me) it is impossible to give you a satisfying answer without asking you questions and that is the other way around...

having said that: welcome to the forum

_________________
my synth
Back to top
View user's profile Send private message Visit poster's website
gabbagabi



Joined: Nov 29, 2008
Posts: 651
Location: Berlin by n8
Audio files: 23

PostPosted: Fri Sep 21, 2018 3:04 am    Post subject: Reply with quote  Mark this post and the followings unread

Berlin in da Houze! party!

As Senhor Grumble already wrote down the essentials of "good asking", i will only say: hello and welcome to the forum!

If you feel like write in german, feel free to pm me.

cu,bb
gabbagabi
Back to top
View user's profile Send private message
ludo



Joined: Sep 20, 2018
Posts: 4
Location: Berlin

PostPosted: Fri Sep 21, 2018 8:21 am    Post subject: Reply with quote  Mark this post and the followings unread

Hi to all! Smile

Tha adsr is working like a a/r generator. The attack and release pots are working well, but the decay and sustain pots are simply do nothing. I checked the schematic few times, but cant find any mistakes.[/img]
The photo was taken when all pots at ca 30%


2018-09-21 17.10.49.jpg
 Description:
 Filesize:  2.94 MB
 Viewed:  375 Time(s)
This image has been reduced to fit the page. Click on it to enlarge.

2018-09-21 17.10.49.jpg


Back to top
View user's profile Send private message
ludo



Joined: Sep 20, 2018
Posts: 4
Location: Berlin

PostPosted: Fri Sep 21, 2018 8:29 am    Post subject: Reply with quote  Mark this post and the followings unread

http://www.yusynth.net/Modular/Commun/ADSR/ADSR555-FINAL.gif
Back to top
View user's profile Send private message
gabbagabi



Joined: Nov 29, 2008
Posts: 651
Location: Berlin by n8
Audio files: 23

PostPosted: Fri Sep 21, 2018 8:58 am    Post subject: Reply with quote  Mark this post and the followings unread

first impulse-guessing: check if D4 is soldered in, in the rigth direction

then i would see how pin12/U2d is behaving, while attacking there should be 15V present, after attack (output reaching 10V) it should change to the sustain voltage, while release it should go back to 15V.
Back to top
View user's profile Send private message
ludo



Joined: Sep 20, 2018
Posts: 4
Location: Berlin

PostPosted: Wed Nov 07, 2018 11:34 am    Post subject: Reply with quote  Mark this post and the followings unread

Problem solved! Smile

There was a failure in the pcb, Pin 1 Of the 7555 Chip was not connected to ground, but instead Pin 2 was connected to ground!

Now i'm happy to have a nice ADSR Very Happy

Thanks for help! Smile
Back to top
View user's profile Send private message
gabbagabi



Joined: Nov 29, 2008
Posts: 651
Location: Berlin by n8
Audio files: 23

PostPosted: Wed Nov 07, 2018 11:40 am    Post subject: Reply with quote  Mark this post and the followings unread

cheers
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic Moderators: Scott Stites
Page 1 of 1 [8 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
 Forum index » DIY Hardware and Software » YuSynth
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Forum with support of Syndicator RSS
Powered by phpBB © 2001, 2005 phpBB Group
Copyright © 2003 through 2009 by electro-music.com - Conditions Of Use