electro-music.com   Dedicated to experimental electro-acoustic
and electronic music
 
    Front Page  |  Articles  |  Radio
 |  Media  |  Forum  |  Wiki  |  Links  |  Store
Forum with support of Syndicator RSS
 FAQFAQ   CalendarCalendar   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   LinksLinks
 RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in  Chat RoomChat Room 
Live streaming at radio.electro-music.com

  host / artist show at your time
  EdisonRex Edison's Electronic Review
Please visit the chat
 Forum index » DIY Hardware and Software » Klee sequencer
Noob working out Klee build for the Bridechamber front panel
Post new topic   Reply to topic Moderators: Scott Stites, Uncle Krunkus, v-un-v
Page 1 of 1 [6 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
Author Message
sync24



Joined: Aug 08, 2009
Posts: 19
Location: UK

PostPosted: Wed Jan 06, 2010 3:35 pm    Post subject: Noob working out Klee build for the Bridechamber front panel Reply with quote  Mark this post and the followings unread

hello,
I'll just start by saying thanks for the electro-music Klee Sequencer, I'm finding everything surrounding it very inspiring!!!
Ok, I've been getting stuck-in to attempting to understand as much as I think I need to get through building this.
The only prior experience of doing this sort of thing before is building a MFOS WSG kit and digging around online to work out how to build an atari punk console.

What I'm trying to get my head around at the moment are the optional features in relation to the Bridechamber front panel I have.

I've been searching the forum here for answers, but there's a couple I am still a little stuck with.
I may be jumping the gun a little as I probably don't fully understand the issue due to not having actually arrived at it in my build process.
So please do forgive me if I'm asking any really dumb questions, this is all pretty new to me!

Ok, so here I go...

First Q:
Optional Voltage Control Outputs - Output A, Output A+B and Output B and associated Glide controls.
In the Klee build issue 6 pdf it states the outputs are provided on J3 on the Analog Board through a 6 pin connector (P1).
Looking up J3 in the pdf, the 8 pins there appear to connect to the 9 thru 16 switches of the Gate Bus (P55 Fig 6-2).
Where is the 6 pin connector? Should it be J13 instead (P64 Fig6-17)?

Second Q:
Variable Range Control Options.
Regarding Option 1 - I'm going to stick a 150k in R33 (as mentioned >>here<<), that's fine.
When it comes to the other options, am I right in thinking that the Bridechamber panel is set up for Option 4 - EXT RANGE on the left of the panel is ready for a jack socket and switch, and I follow P38, Fig 4-16?

Third Q:
Optional External Load Enable Switch.
Same deal as prev Q really, panel is ready with EXT LOAD on the left waiting for a jack socket and switch, and I follow P36, Fig 4-13?

The last two options I think I'm cool with. I've got old Roland gear so have gone for the 5V gate and trigger option (the parts kit I got from here didn't have the 1k5 resistors though so I need to get some).
The Automated Range Switch Data Inputs I don't know what that means, so I'll leave on a high note!

Thanks in advance for help with this!
Duff
Back to top
View user's profile Send private message Visit poster's website
patchdub



Joined: Jan 21, 2009
Posts: 56
Location: Taos, NM

PostPosted: Sun Jan 10, 2010 8:03 pm    Post subject: Reply with quote  Mark this post and the followings unread

hi. i am almost finished wiring my klee with the bridechamber panel. whew! its alot of wires.

1 ?- yes j13
2 ?- yes option 4 on pg 38
3 ?- yes

hope this helps.

the only question i still have is how to wire the clock thru jack.

_________________
www.patchdub.com
Back to top
View user's profile Send private message Visit poster's website
sduck



Joined: Dec 16, 2007
Posts: 443
Location: Nashville
Audio files: 5

PostPosted: Mon Jan 11, 2010 10:38 am    Post subject: Reply with quote  Mark this post and the followings unread

patchdub wrote:


the only question i still have is how to wire the clock thru jack.


AFAIK the clock thru jack is just a straight connection to the clock in jack - basically it's just a small built in multiple. There's nothing on the pcb's that would connect to it, at least on the versions I have.
Back to top
View user's profile Send private message
patchdub



Joined: Jan 21, 2009
Posts: 56
Location: Taos, NM

PostPosted: Mon Jan 11, 2010 7:15 pm    Post subject: Reply with quote  Mark this post and the followings unread

thanks sduck!
all done wiring. tried so hard to keep it nice and tidy but at some point it just got out of hand
about to power up. fingers crossed!


kleewire.jpg
 Description:
 Filesize:  18.32 KB
 Viewed:  3974 Time(s)

kleewire.jpg



_________________
www.patchdub.com
Back to top
View user's profile Send private message Visit poster's website
Uncle Krunkus
Moderator


Joined: Jul 11, 2005
Posts: 4760
Location: Sydney, Australia
Audio files: 52
G2 patch files: 1

PostPosted: Tue Jan 12, 2010 1:47 am    Post subject: Reply with quote  Mark this post and the followings unread

I included the "auto range control" links just in case anyone wanted to tap into the three bits which control the range and make them programmable or clockable from external sources etc. The default is to leave those links on the board and just wire the rotary as shown.
_________________
What makes a space ours, is what we put there, and what we do there.
Back to top
View user's profile Send private message Visit poster's website
sync24



Joined: Aug 08, 2009
Posts: 19
Location: UK

PostPosted: Fri Jan 15, 2010 1:16 am    Post subject: Reply with quote  Mark this post and the followings unread

thanks for the replies peolpe!
i think i'm getting there with this build,
term started again this week though, so life is hectic again...
i'll no doubt be back with a couple more Qs soon,

thanks again!
duff
Back to top
View user's profile Send private message Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic Moderators: Scott Stites, Uncle Krunkus, v-un-v
Page 1 of 1 [6 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
 Forum index » DIY Hardware and Software » Klee sequencer
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
e-m mkii

Please support our site. If you click through and buy from
our affiliate partners, we earn a small commission.


Forum with support of Syndicator RSS
Powered by phpBB © 2001, 2005 phpBB Group
Copyright © 2003 through 2009 by electro-music.com - Conditions Of Use